Tablet as USB host, Orin's stock L4T gadget as the network side: the
tablet chose NCM and got 192.168.55.100. Android only routes app traffic
over it once it is the default network, so the app has to bind to the
Ethernet network explicitly.
Mass storage is off (enable_ums=0); the config isn't a conffile, so an
nvidia-l4t-init upgrade restores it and the report says how to check.
The Orin's USB-C port (FUSB301, no PD) can't charge the tablet; the PD
hub on hand is the practical fix.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The car unit has no display of its own (the tablet app is the display),
and unified memory is better spent on the voice stack. GDM/GNOME no
longer start, a text login stays on tty1, and PulseAudio/PipeWire are
disabled for all users while ALSA stays for mic capture. Saves ~200 MB
idle; every step is a reversible disable, not a removal.
Also notes the pre-existing nightly logrotate failure from the NVIDIA
jetson-logging config.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
project-yukart's map-tile sync treats NetworkManager's metered flag as
a second guard against syncing over LTE; the flag was never set. It is
now, live on the car unit.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
With the WiFi radio off, the default route moved to wwan0 within 10 s and
all IPv4/DNS/Tailscale samples passed. Tailscale went direct to halogen
over povo's global IPv6 (no DERP), and an SSH session over the tailnet
survived both switches. WiFi took back IPv4 within 15 s and IPv6 within
~45 s.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The backup pin doesn't charge, so a rechargeable ML2032 would just
drain with a third of the capacity. Adds the expected life (~1.5-2 yr
typical), polarity and post-fit test notes, and marks the item low
priority since NTP covers almost every online boot.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The dev kit carrier has pads but no connector populated, so the RTC
resets whenever power is removed. Captures the connector part NVIDIA's
docs reportedly specify, the community substitute, and the R560 note;
battery type and footprint still need checking against the schematic.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
timesyncd now uses ntp.nict.jp (stratum 1), with the JP pool and Ubuntu
as fallback, over whichever uplink holds the default route. Timezone
moves from Asia/Yakutsk to Asia/Tokyo: same offset, right place.
Records that the RTC loses time at power-off (the cold boot came up at
June 4 until NTP synced), and the planned chrony + gpsd setup once
GNSS has a fix.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
With both adapters attached at power-on, pcan registered first and took
can0, and the udev rule renamed it to can_pcan, confirming the race and
the fix. qmi_wwan auto-loaded, povo auto-connected below WiFi, and gpsd
came up on the stable symlink.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The driver source sat in /tmp and was gone after a reboot, leaving the
"after a kernel update" steps unusable. Re-fetched PEAK 9.2.0 into
~/infra/peak-linux-driver-9.2.0 per GUIDELINES §1; it is the same
release as the installed pcan.ko (Release_20260707_n).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
mttcan and pcan both load at boot, so the PCAN adapter could take can0
and push the onboard controller to can1. A udev rule now names them
can_onboard (platform c310000.mttcan) and can_pcan (USB 0c72:000c),
both outside the canN pool so a transient canN can never collide.
Also records why the SIM7600 needs nothing more: ModemManager and NM
don't use ttyUSB numbers, and gpsd already uses a symlink.
can_onboard is verified live; can_pcan is checked against the driver
source only (adapter not plugged in).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The L4T kernel ships without qmi_wwan/cdc-wdm, and PPP dial-up made KDDI
detach the povo SIM (attach APN was au's; PPP re-activating the default
bearer still detached). Built both modules out of tree from v5.15.148
into ~/infra/qmi_wwan, set the attach APN to povo.jp, and added an NM
connection at metric 1000 so LTE ranks below Ethernet and WiFi.
GNSS autostarts on the modem and gpsd reads /dev/sim7600-gps (udev
symlink on interface 01); no fix yet, tested indoors.
BOM: NMEA is on ttyUSB1 not ttyUSB3, and the data path is QMI, not
RNDIS/PPP.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The original report was written on another host. On this machine the
pcan module (NETDEV_SUPPORT) is built, installed under misc/, and loaded
at boot via /etc/modules; the adapter was not yet plugged in. Adds the
verification and post-kernel-update rebuild steps.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The Orin Nano Developer Kit exposes no DSI connector — the module carries DSI
on SODIMM pins but the reference carrier board does not break them out, and
DisplayPort is its only display output. The Waveshare panel is also a
Raspberry Pi accessory and mechanically incompatible. It could not have been
connected without a custom carrier board.
Moot regardless: the tablet is the display, and no dedicated display is in
scope. The entry was still marked research pending / TBD.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_013kj58Jugkic783b8ZrtTVZ
Replaces `type: default` — one value across every document, read by nothing.
Types are now reference, guidelines, plan and report; plans carry status and
updated, reports carry date. Convention documented in project-yukart REPOS.md.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_013kj58Jugkic783b8ZrtTVZ
mikkeli
mikkeli