mikkeli
4742d4a5bb
The L4T kernel ships without qmi_wwan/cdc-wdm, and PPP dial-up made KDDI detach the povo SIM (attach APN was au's; PPP re-activating the default bearer still detached). Built both modules out of tree from v5.15.148 into ~/infra/qmi_wwan, set the attach APN to povo.jp, and added an NM connection at metric 1000 so LTE ranks below Ethernet and WiFi. GNSS autostarts on the modem and gpsd reads /dev/sim7600-gps (udev symlink on interface 01); no fix yet, tested indoors. BOM: NMEA is on ttyUSB1 not ttyUSB3, and the data path is QMI, not RNDIS/PPP. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
146 lines
6.8 KiB
Markdown
146 lines
6.8 KiB
Markdown
---
|
|
type: report
|
|
date: 2026-10-07
|
|
---
|
|
# SIM7600G-H-M.2 (LTE + GNSS) Setup on Jetson Orin Nano
|
|
|
|
## Result
|
|
|
|
| Item | State |
|
|
|------|-------|
|
|
| LTE data via ModemManager + NetworkManager (QMI, `wwan0`) | Working: IPv4 + IPv6, ~9 Mbit/s DL observed |
|
|
| Route priority: Ethernet (100) > WiFi (600) > LTE (1000) | Working |
|
|
| GNSS engine + gpsd on `/dev/sim7600-gps` | Pipeline working; satellites seen, **no fix yet** (tested indoors) |
|
|
|
|
## Hardware
|
|
|
|
- **Board:** Jetson Orin Nano, hostname `mikkeli-orin-nano`, kernel `5.15.148-tegra` (L4T 36.4.4)
|
|
- **Modem:** Waveshare SIM7600G-H-M.2 on the SIM7600G-H-M2 4G HAT, connected over USB
|
|
- USB ID `1e0e:9001` (default composition, `AT+CUSBPIDSWITCH?` → `9001`)
|
|
- Firmware `LE20B04SIM7600G-H-M2` / `SIM7600G_V2.0.2`
|
|
- **SIM:** povo (KDDI/au MVNO), APN `povo.jp`, no user/password. Registers as `KDDI KDDI` (44051), LTE band 18.
|
|
|
|
### USB interfaces (PID 9001)
|
|
|
|
| Iface | Port | Driver | Role (as ModemManager sees it) |
|
|
|-------|------|--------|-------------------------------|
|
|
| 0 | ttyUSB0 | option | diagnostics (ignored) |
|
|
| 1 | ttyUSB1 | option | **NMEA GPS** → `/dev/sim7600-gps` |
|
|
| 2 | ttyUSB2 | option | AT (primary) |
|
|
| 3 | ttyUSB3 | option | AT |
|
|
| 4 | ttyUSB4 | option | audio |
|
|
| 5 | `cdc-wdm0` + `wwan0` | **qmi_wwan** (self-built) | QMI control + network |
|
|
|
|
## Problems hit and fixes
|
|
|
|
### 1. `sim-missing`: SIM inserted after the modem powered up
|
|
|
|
ModemManager reported `failed reason: sim-missing`, but `AT+CPIN?` returned `READY`. SIM hot-swap is off
|
|
on this module (`AT+UIMHOTSWAPON: 0`), so a SIM seated after power-on isn't noticed until the modem re-initializes.
|
|
Restarting ModemManager (or re-plugging the modem) fixes it.
|
|
|
|
Hot-swap was deliberately left off. Turning it on needs the right `AT+UIMHOTSWAPLEVEL` for the HAT's SIM-detect
|
|
wiring, and getting that wrong makes the modem report "no SIM" permanently. **Insert the SIM before powering the modem.**
|
|
|
|
### 2. Tegra kernel has no `qmi_wwan` / `cdc-wdm`
|
|
|
|
`CONFIG_USB_NET_QMI_WWAN` and `CONFIG_USB_WDM` are unset in the stock L4T kernel, so interface 5 had no driver,
|
|
leaving PPP over a ttyUSB port as the only data path. Fixed by building both modules out of tree from
|
|
upstream stable `v5.15.148` (see [rebuild](#rebuilding-qmi_wwan-after-a-kernel-update)).
|
|
|
|
### 3. PPP dial causes `NW DETACH` on KDDI
|
|
|
|
With PPP, every `ATD*99***<cid>#` ended about 32 s later with `NO CARRIER` + `+CGEV: NW DETACH`, `+CEER: No service available`.
|
|
Two causes:
|
|
|
|
- PDP context 1 (the LTE **initial-attach** APN) was preset to `au.au-net.ne.jp`, which a povo SIM can't use, and ModemManager put `povo.jp`
|
|
on a new context 5. Fixed by setting context 1 to `povo.jp` (see below). After that the attach itself brings up a default bearer with an address.
|
|
- Even with that fixed, a PPP dial on context 1 still triggered a network detach: PPP tries to activate a context that is already the
|
|
active default bearer. **QMI does not have this problem**: it uses the existing default bearer. Do not use PPP with this SIM.
|
|
|
|
Setting the attach APN (with ModemManager stopped; the setting persists in modem NVRAM):
|
|
|
|
```
|
|
AT+CFUN=4 # radio off, SIM stays powered (CFUN=0 powers the SIM down → CGDCONT returns ERROR)
|
|
AT+CGDCONT=1,"IPV4V6","povo.jp"
|
|
AT+CGDCONT=5 # remove stray contexts ModemManager had created
|
|
AT+CFUN=1
|
|
AT+CGPADDR=1 # should now show an IPv4 + IPv6 address
|
|
```
|
|
|
|
## Configuration applied
|
|
|
|
### Kernel modules
|
|
|
|
Source + Makefile live in `~/infra/qmi_wwan/` (per [GUIDELINES §1](../../GUIDELINES.md)):
|
|
|
|
```
|
|
~/infra/qmi_wwan/
|
|
├── Makefile # obj-m += cdc-wdm.o qmi_wwan.o ; `make install` → /lib/modules/$(uname -r)/misc/ + depmod
|
|
├── cdc-wdm.c # linux-stable v5.15.148 drivers/usb/class/cdc-wdm.c
|
|
└── qmi_wwan.c # linux-stable v5.15.148 drivers/net/usb/qmi_wwan.c (has QMI_QUIRK_SET_DTR(0x1e0e, 0x9001, 5))
|
|
```
|
|
|
|
Installed to `/lib/modules/5.15.148-tegra/misc/{cdc-wdm,qmi_wwan}.ko`. They auto-load through the USB modalias after `depmod`,
|
|
so no `/etc/modules` entry is needed.
|
|
|
|
### NetworkManager connection `povo`
|
|
|
|
```
|
|
sudo nmcli con add type gsm ifname '*' con-name povo gsm.apn povo.jp \
|
|
connection.autoconnect yes connection.autoconnect-retries 0 \
|
|
ipv4.route-metric 1000 ipv6.route-metric 1000 ipv6.method auto
|
|
```
|
|
|
|
- `ifname '*'`: binds to whichever modem ModemManager exposes (now `cdc-wdm0`).
|
|
- `autoconnect-retries 0` (forever): the default of 4 retries left the link permanently down after early failures. In a car, the modem may
|
|
come up after NetworkManager.
|
|
- Metric 1000 vs NM defaults Ethernet 100 / WiFi 600 → LTE only carries traffic when both are gone. Right after connecting the route
|
|
can briefly show metric 21000 (NM's +20000 penalty until its connectivity check passes); it settles to 1000.
|
|
|
|
Check:
|
|
|
|
```
|
|
mmcli -m any # state: connected, primary port: cdc-wdm0
|
|
ip route show default # wlP1p1s0 metric 600, wwan0 metric 1000
|
|
curl --interface wwan0 https://ifconfig.me
|
|
```
|
|
|
|
### GNSS
|
|
|
|
- GNSS engine was already running (`AT+CGPS?` → `1,1`). Set to start on boot: `AT+CGPSAUTO=1` (persists in modem).
|
|
- ModemManager location is **not** used. gpsd owns the NMEA port; ModemManager only labels it `(gps)` and leaves it unopened.
|
|
- Stable device name, `/etc/udev/rules.d/99-sim7600-gps.rules`:
|
|
```
|
|
SUBSYSTEM=="tty", ATTRS{idVendor}=="1e0e", ATTRS{idProduct}=="9001", ENV{ID_USB_INTERFACE_NUM}=="01", SYMLINK+="sim7600-gps"
|
|
```
|
|
- `apt install gpsd gpsd-clients`, `/etc/default/gpsd`:
|
|
```
|
|
DEVICES="/dev/sim7600-gps"
|
|
GPSD_OPTIONS="-n"
|
|
USBAUTO="false" # hotplug would let gpsd probe the modem's AT ports and conflict with ModemManager
|
|
```
|
|
- `systemctl enable --now gpsd.socket gpsd`
|
|
|
|
Check: `cgps` or `gpspipe -w -n 10`. On 2026-10-07, tested indoors, gpsd saw `nSat: 10, uSat: 0`, `mode: 1` (no fix).
|
|
Next: test with the GNSS antenna (IPEX, labeled GNSS on the HAT) with a clear view of the sky. A cold start can take a few minutes.
|
|
|
|
## Rebuilding qmi_wwan after a kernel update
|
|
|
|
Out-of-tree modules do not survive a kernel update. Signs: ModemManager shows `primary port: ttyUSB2` and there is no `/dev/cdc-wdm0`.
|
|
|
|
```
|
|
cd ~/infra/qmi_wwan
|
|
# if the kernel's upstream base version changed, refresh the sources:
|
|
# V=v5.15.xxx; for f in drivers/net/usb/qmi_wwan.c drivers/usb/class/cdc-wdm.c; do
|
|
# curl -fL -o $(basename $f) "https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/plain/$f?h=$V"; done
|
|
make clean && make && sudo make install
|
|
sudo modprobe qmi_wwan && sudo systemctl restart ModemManager
|
|
```
|
|
|
|
## Useful one-offs
|
|
|
|
- Talk to the modem directly: `sudo systemctl stop ModemManager`, then use a terminal on `/dev/ttyUSB2`; start ModemManager again afterwards.
|
|
(ModemManager holds ttyUSB2/3 while running.)
|
|
- Verbose ModemManager log incl. AT traffic: `sudo mmcli -G debug` then `journalctl -u ModemManager -f` (resets on restart).
|