mikkeli
acb47b48ef
Finds the module itself (every non-modem adapter, 115200 then 9600), so the adapter can be swapped. Mounting by --forward/--right; attitude from a complementary filter on gravity (gyro through motion, accelerometer near 1 g); gravity removed from acceleration; yaw rate left-positive. Never writes to the module. dialout via SupplementaryGroups. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com> Claude-Session: https://claude.ai/code/session_01DDwfd6Ki8UfG4hK6W5YpJz
3.6 KiB
3.6 KiB
type
| type |
|---|
| reference |
Core services
Part of Project Yukart, making an old 2008 Mitsubishi Z27AG a bit smarter with modern technologies.
This file serves as the minimalist portal to other docs
What this repo is about
The acquisition and processing cluster on the Orin, developed and deployed as one
unit: recorder, decoder, gnss, imu, orin-status and obd-poller now; can-bridge as it is
needed.
| Binary | Installed as | Does |
|---|---|---|
recorder |
yukart-recorder.service |
Raw CAN + GNSS to disk, in sessions, under a storage bound; every yukart/vehicle/* value (decoded and OBD-II) beside them |
decoder |
yukart-decoder.service |
The car's own broadcast frames to named signals (yukart/vehicle/*): every z27ag signal in contracts' signals.json, laid out by its can block. Booleans on change, numbers ≤ 20/s, each refreshed once a second; reads only |
bus-bench |
not installed: a test tool | Raw CAN and decoded-signal load over MQTT, measured: loss, latency, broker CPU (report) |
obd-poller |
yukart-obd-poller.service |
OBD-II mode 01 on the K-line through the Bluetooth ELM327 (address in /etc/default/yukart-elm), the single writer to the car; never on CAN. The obd_* signals, calibration references (yukart/vehicle/*): rpm, speed, throttle, load, MAF, timing, O2 every round; temperatures and trims every 5 s. Lets go of the adapter after a minute of ECU silence |
gnss |
yukart-gnss.service |
gpsd's fix as single values on yukart/gnss/*: fix, speed, heading, position, altitude, satellites |
imu |
yukart-imu.service |
The WT61 (plus) on any USB-UART adapter, found by itself (adapter and speed), turned into the car's frame (--forward, --right): roll, pitch, gravity-free longitudinal and lateral g, yaw rate on yukart/imu/*, at most every 40 ms. Never writes to the module |
orin-status |
yukart-orin-status.service |
The Orin's health on the bus, once a second: temperatures, CPU/GPU load, memory, power, fan, WiFi (with SSID)/LTE/tablet links, the CAN interface, the ELM's Bluetooth link, UPS battery (yukart/host/*) |
scripts/deploy-recorder.sh # build, glibc check, install on the car Orin
scripts/deploy-native.sh BIN # build BIN on the development Orin, glibc check, install;
# deploy-{decoder,gnss,obd-poller,orin-status}.sh wrap it.
# Redeploy after any contracts signals.json change
yukart-decoder --list # the signals it decodes, and where
zstdcat can-*.log.zst | yukart-decoder --replay # what it would publish for a recording
yukart-obd-poller --elm ADDR --once # on the Orin, service stopped: adapter, protocol,
# supported PIDs and one value each
yukart-gnss --once # the next fix as JSON, no broker
yukart-imu --once # find the WT61, 3 s of readings as JSON, no broker
yukart-orin-status --once # on an Orin: one reading as JSON, no broker
yukart-recorder ctl status # on the Orin
yukart-recorder ctl start "cold start" # manual session, ends only on stop
yukart-recorder ctl mark "indicator left on"
yukart-recorder ctl stop
Recordings live in /var/lib/yukart/recordings/, one directory per session —
layout in the initial plan.
- For implementation practice guidelines, refer to the guidelines;
- For implementation plans and history, refer to them;